Manual d'usuari Fisher-Price K2566 Crib

Manual d'usuari pel dispositiu Fisher-Price K2566 Crib

Manual d'usuari Fisher-Price K2566 Crib

Extractes de continguts

Resum a la pàgina de contingut no. 1

K2566WARNINGIMPORTANT! KEEP INSTRUCTIONSFOR FUTURE REFERENCE.www.fisher-price.co.uk

Resum a la pàgina de contingut no. 2

Consumer Information• Please read these instructions before assembly and use ofthis product.• Adult assembly is required.• Tool required for assembly: Phillips screwdriver(not included).• Requires four “D” (LR20) alkaline batteries (not included)for operation.• Product features and decorations may varyfrom photographs.WARNINGTo prevent serious injury or death:• Fall Hazard – It is dangerous to usethis reclined cradle on an elevatedsurface, since child’s movement maycause prod

Resum a la pàgina de contingut no. 3

PartsIMPORTANT! Please remove all parts from the package and identify them before assembly.Some parts may be packed in the pad.Seat Back TubeToy Bar2 RetainersPadFootrest with Soothing UnitBase Tube2 FeetLeft Base WireRight Base Wire#8 x 1,9 cm Screw – 2M5 x 20 mm Screw - 2Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.3

Resum a la pàgina de contingut no. 4

Battery InstallationAssemblyIMPORTANT! Before assembly and each use, inspect this productfor damaged hardware, loose joints, missing parts or sharp edges.DO NOT use if any parts are missing or broken. Contact Mattel forreplacement parts and instructions if needed. Never substitute parts.Hint: We recommend using alkaline batteries forlonger battery life.Base Tube1,5V x 4“D” (LR20)Left Base Wire1Right Base Wire• Place the base tube on a flat surface.• Position the left and right base wires

Resum a la pàgina de contingut no. 5

AssemblyRetainersSeat Back TubeBase WireBase Wire3• Insert an M5 x 20 mm screw through each foot and tighten.Flex Base Wires InwardPull Up5Tabs• Position the seat backtube above the baseassembly.• Fit the seat back tubecompletely onto thebase wires.• Fit a retainer (roundedside inward) to oneend of the seat back tube.• Insert a #8 x 1,9 cm screw through the outside hole inthe seat back tube and into the retainer.• While holding the retainer in place, tighten the screw.• Repeat this

Resum a la pàgina de contingut no. 6

AssemblyLatch6Tab7• Fit the pad upper pocket onto the seat back tube.• Fit the pad lower pocket onto the footrest.• Fit the toy bar ends into the sockets in the footrest.Hint: The square end of the toy bar fits into the squaresocket and the circular end of the toy bar fits into thecircular socket.• Make sure the toy bar latches are secure. The small tabs onthe sockets should be visible in the opening in the latches.Assembly is now complete.6

Resum a la pàgina de contingut no. 7

Setup and UseTIGHTENFree EndWARNINGTo prevent serious injury or death:• Fall Hazard – It is dangerous to usethis reclined cradle on an elevatedsurface, since child’s movement maycause product to slide or tip over. Useonly on a floor.• Suffocation Hazard – Never use ona soft surface (bed, sofa, cushion),since product can tip over and causesuffocation in soft surfaces.• Always use the restraint system.• Never leave child unattended.• Never use as a car seat.• Never use as a carri

Resum a la pàgina de contingut no. 8

Setup and UseLatch5Remove the Toy Bar• Pull the ends of the latches and lift the toy bar.CareThe pad is machine washable. Wash the pad separately incold water on the gentle cycle. Do not use bleach. Tumbledry separately on low heat and remove promptly. The frame,toy bar can be wiped clean using a mild cleaning solution anddamp cloth. Do not use bleach. Do not immerse the soothingunit or toy bar.4Mode SwitchRainforest Soundsor Music SwitchVolume ButtonRainforest Sounds or Music• Slide the swi

DEIXA UN COMENTARI