Manual d'usuari Kenwood DDX5036M GPS Receiver

Manual d'usuari pel dispositiu Kenwood DDX5036M GPS Receiver

Manual d'usuari Kenwood DDX5036M GPS Receiver

Extractes de continguts

Resum a la pàgina de contingut no. 1

GPS NAVIGATION SYSTEMDNX SERIESDNX5360 DNX5360MMONITOR WITH DVD RECEIVERDDX SERIESDDX5036 DDX5036MINSTALLATION MANUAL© B54-4766-10/01 (MW/M2W/XW)

Resum a la pàgina de contingut no. 2

Accessories1Installation Procedure0*..........12..........2!*DNX SERIES only..........13DNX SERIES only..........14..........1* Accessory of DNX5360M.This accessory is used whenconnecting an externaldevice to AV-IN jack on thefront panel of this unit. Forhow to use this accessory,refer to the instructionmanual of this unit...........152WARNING• If you connect the ignition wire (red) and the battery wire(yellow) to the car chassis (ground), you may cause a shortcircuit, that in turn may start a

Resum a la pàgina de contingut no. 3

¤• Mounting and wiring this product requires skills andexperience. For safety’s sake, leave the mounting and wiringwork to professionals.• Make sure to ground the unit to a negative 12V DC powersupply.• Do not install the unit in a spot exposed to direct sunlightor excessive heat or humidity. Also avoid places with toomuch dust or the possibility of water splashing.• Do not use your own screws. Use only the screws provided.If you use the wrong screws, you could damage the unit.• If

Resum a la pàgina de contingut no. 4

Connectionyou connect the ignition wire (red) and the battery¤ Ifwire(yellow) to the car chassis (ground), you mayIgnition keyswitchcause a short circuit, that in turn may start a fire. Alwaysconnect those wires to the power source runningthrough the fuse box.ACCABACar fuse boxBCar fuse box(Main fuse)CIgnition wire (Red)Battery wire (Yellow)Ground wire (Black) (To car chassis)Antenna CordFM/AMantenna inputCBatteryto the vehicle's parking brake⁄ Connectdetection switch harness.Parking sensor w

Resum a la pàgina de contingut no. 5

GPS Antenna (Accessory 2)(see page 8)FUSE ( 15A )Accessory 1REVERSEREMOTE CONTSTEERING WHEELREMOTE INPUTWhite/BlackWhite+To front left speakerGray/BlackILLUMIGrayMUTE+To front right speakerGreen/BlackGreen+To rear left speakerPurple/BlackANT. CONTPurple+To rear right speakerP CONTEnglish |5

Resum a la pàgina de contingut no. 6

System ConnectionUSB terminalUSB device(commercially available)Rear View Camera input• Visual input (Yellow)Audio/Visual output• Visual output (Yellow)• Audio left output (White)• Audio right output (Red)Visual input (iPod/AV input 2 switchable)Resistance-free mini plug (3.5φ)Audio input (iPod/AV input 2 switchable)Resistance-free stereo type mini plug (3.5φ)Rear Preout• Audio left output (White)• Audio right output (Red)Front Preout• Audio left output (White)• Audio right outp

Resum a la pàgina de contingut no. 7

Optional Accessory ConnectioniPod(commercially available)KCA-iP301V(Optional Accessory)Audio Output (Black)Visual Output (Yellow)(DDX5036/ DDX5036M only)USB terminalNavigation System(Optional Accessory)Connection cable(Included in theNavigation System)KCA-BT200 (Optional Accessory) inputTV Tuner (Optional Accessory)TV ANTENNA INPUTTO MONITOR UNIT⁄Navigation units that can be connectedto this unit. (As of December, 2009):KNA-G630KNA-G630CNFor latest information, access thewww.kenwood.com/cs/ce/

Resum a la pàgina de contingut no. 8

Installing the GPS Antenna(DNX SERIES only)GPS antenna is installed inside of the car. It shouldbe installed as horizontally as possible to allow easyreception of the GPS satellite signals.To mount the GPS antenna inside your vehicle:1. Clean your dashboard or other surface.2. Peel the backing off of the adhesive on the bottomof the metal plate (accessory 3).3. Press the metal plate (accessory 3) down firmly onyour dashboard or other mounting surface. You canbend the metal plate (accessory 3) to

Resum a la pàgina de contingut no. 9

Installing the EscutcheonInstalling the EscutcheonFor Toyota/Scion1. Attach accessory 4 to the unit.1. Cut out accessory 5 as illustrated.Cutting lineAccessory 5Accessory 4For General Motors1. Cut out accessory 5 to meet the shape of theopening of the center console.2. Attach accessory 5 to the unit.Cut out to meet the shape ofthe opening in the vehicle.2. Fold double-sided adhesive (accessory 6) alongthe slit and attach it to accessory 5 cut-outagainst the center rib as illustrated. Use 2 piece

Resum a la pàgina de contingut no. 10

Installation for Monitor/Player UnitInstallation on Toyota, Nissan or Mitsubishi Car using BracketsAccessory 7 (M5x6mm)or Accessory 8 (M5x7mm)Car BracketAccessory 7 (M5x6mm)or Accessory 8 (M5x7mm)10 |DNX SERIES/ DDX SERIES

Resum a la pàgina de contingut no. 11

English |11

DEIXA UN COMENTARI